داده های ثبت شده در پورتال
1
Daavood Mirahmadi Khaki, Kamran Dehghani, Ali Shamsipoor, Ali Kalaki,
"Mechanism of self-healing behavior in rolled Cu-2Be flat product", ENGINEERING FAILURE ANALYSIS,
Vol. 156,
Num. 156,
Page 1-13,
December 2023,
2
Majid Vaghari, Kamran Dehghani,
"Computational and experimental investigation of a new non equiatomic FCC single-phase Cr15Cu5Fe20Mn25Ni35 high-entropy alloy", PHYSICA B-CONDENSED MATTER,
Vol. -,
Num. 671,
Page 1-9,
October 2023,
3
Amirhossein Hosseinifar, Kamran Dehghani,
"The simulation of texture of Al0.3CoCrFeNi high entropy alloy after cold deformation using visco-plastic self-consistent model", Iranian journal of Materials Forming,
Vol. 10,
Num. 1,
Page 53-60,
May 2023,
4
Mehrab Seyfpoor Byjnavandi, Armin Ghaderi, Kamran Dehghani,
"Effect of Cold Rolling on the Microstructure Evolution, Mechanical, and Corrosion Properties of AlCoCrFeNi2.4 High-Entropy Alloy", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 71,
Num. 1,
Page 1-15,
March 2023,
5
Daavood Mirahmadi Khaki, Kamran Dehghani, Ali Shamsipoor, Ali Kalaki,
"Hot deformation behavior, microstructure evolution and processing map of Cu–2Be alloy", Journal of Materials Research and Technology,
Vol. 24,
Num. 0,
Page 376-394,
March 2023,
6
Seyed Ali Erfani Mobarakeh, Kamran Dehghani,
"Nanocomposite AlCoCrFeNi2.1 high-entropy alloy produced by FSP", Journal of Materials Research and Technology,
Vol. 19,
Num. 5,
Page 765-778,
May 2022,
7
Seyed Ali Erfani Mobarakeh, Kamran Dehghani,
"Thermo-Mechanical Treatment of AlCoCrFeNi2.1 High-Entropy Alloy", Iranian journal of Materials Forming,
Vol. 9,
Num. 1,
Page 41-46,
February 2022,
8
Seyed Ali Erfani Mobarakeh, Taranom Seyedhosseini, Kamran Dehghani,
"Tribological and mechanical properties of surface nanocomposite
AlCoCrFeNi2.1 high-entropy alloy produced by FSP", JOURNAL OF ALLOYS AND COMPOUNDS,
Vol. 896,
Num. 17,
Page 163052-163063,
December 2021,
9
Armin Ghaderi, Hossein Moghanni Alghalandis, Kamran Dehghani,
"Microstructural Evolution and Mechanical Properties
of Al0.5CoCrFeNi High-Entropy Alloy after Cold Rolling
and Annealing Treatments", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 30,
Num. 10,
Page 7817-7825,
July 2021,
10
A. Abbasi, Kamran Dehghani, V. Sajadifar, T. Niendorf,
"Quenching of High Entropy Alloys after Annealing", Iranian journal of materials science and engineering,
Vol. 4,
Num. 17,
Page 130-141,
November 2020,
11
Behrooz Rahmatian, Kamran Dehghani, Seyed Ehsan Mirsalehi,
"Effect of adding SiC nanoparticles to nugget zone of thick AA5083
aluminium alloy joined by using double-sided friction stir welding", Journal of Manufacturing Processess,
Vol. 52,
Num. 0,
Page 152-164,
April 2020,
12
Kamran Dehghani, Shima Akbarian,
"On the molecular dynamics simulation of fatigue behavior of pre-cracked
aluminum chip for NEMS application: Effect of cyclic loading mode and
surface roughness geometry", INTERNATIONAL JOURNAL OF FATIGUE,
Vol. 135,
Num. 105570,
Page 1-11,
March 2020,
13
Hamed Eskandari, Mohsen Saboktakin, Arezoo Ghanbari, Babak Nasiri, Kamran Dehghani,
"A study on the surface severe plastic deformation and corrosion
behavior of an interstitial free steel", Materials Research Express,
Vol. 6,
Num. 12,
Page 1-11,
January 2020,
14
, Kamran Dehghani,
"Hot tensile properties of CoCrFeMnNi(NbC) compositionally complex alloys", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 772,
Num. 1,
Page 138771-138771,
December 2019,
15
, Kamran Dehghani,
"Microstructure and mechanical properties of Co19Cr20Fe20Mn21Ni19 and
Co19Cr20Fe20Mn21Ni19Nb0.06C0.8 high-entropy/compositionally-complex
alloys after annealing", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 772,
Num. 772,
Page 138812-138812,
November 2019,
16
Masoud Mirzadeh, Kamran Dehghani, Milad Rezaei, Zeynab Mahidashti,
"Effect of stearic acid as a low cost and green material on the self-cleaning
and anti-corrosion behavior of anodized titanium", COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS,
Vol. 583,
Num. 123971,
Page 1-10,
September 2019,
17
Behrooz Rahmatian, Seyed Ehsan Mirsalehi, Kamran Dehghani,
"Metallurgical and Mechanical Characterization of Double-Sided Friction Stir Welded Thick AA5083 Aluminum Alloy Joints", TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS,
Vol. 0,
Num. 0,
Page 0-0,
July 2019,
18
Seyed Siavash Firouzabadi, Kamran Dehghani, Malek Naderi, Farzad Mahboubi,
"fracture toughness and plasticity evaluation of sputter deposited tantalum nitride film", ,
Vol. 13,
Num. 1,
Page 103-112,
May 2019,
19
Nima Sharifi Asl, Seyed Ehsan Mirsalehi, Kamran Dehghani,
"Effect of TiO2 nanoparticles addition on microstructure and mechanical properties of dissimilar friction stir welded AA6063-T4 aluminum alloy and AZ31B-O magnesium alloy", Journal of Manufacturing Processess,
Vol. 38,
Num. 0,
Page 338-354,
April 2019,
20
, Kamran Dehghani,
"Effect of Nb-C addition on the microstructure and mechanical properties of
CoCrFeMnNi high entropy alloys during homogenisation", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 753,
Num. 0,
Page 224-231,
March 2019,
21
E. Shafie, Kamran Dehghani, F. Ostovan, M. Toozandehjani,
"Effect of Microstructure and Texture Evolution During Variable Gauge
Rolling on Mechanical Properties of Tailor Rolled Blanks", METALS AND MATERIALS INTERNATIONAL,
Vol. 1,
Num. 1,
Page 1-12,
January 2019,
22
, Kamran Dehghani,
"Phase prediction and microstructure of centrifugally cast non-equiatomic Co-Cr-Fe-Mn-Ni(Nb,C) high entropy alloys", JOURNAL OF ALLOYS AND COMPOUNDS,
Vol. 783,
Num. 0,
Page 292-299,
January 2019,
23
Rasoul Pouriamanesh, Kamran Dehghani,
"study the microstructure and hardness of FSWed steel in the presence of TiO2", ,
Vol. 12,
Num. 3,
Page 121-135,
December 2018,
24
Akbar Jafari, Kamran Dehghani, K. Bahaaddini, R. Abbasi Hataie,
"Experimental comparison of abrasive and erosive wear characteristics of
four wear-resistant steels", WEAR,
Vol. 416–417,
Num. 1,
Page 14-26,
October 2018,
25
Ehsan Shafiei Liravinejad, Kamran Dehghani,
"Effects of Deformation Conditions on the Rolling
Force during Variable Gauge Rolling", Journal of Manufacturing and Materials Processing-OPEN,
Vol. 48,
Num. 1,
Page 2-12,
July 2018,
26
Rasoul Pouriamanesh, Kamran Dehghani, Rudolf Vallant,
"Friction stir welding of API X70 steel incorporating Ti-dioxide", CANADIAN METALLURGICAL QUARTERLY,
Vol. -,
Num. 0,
Page 1-13,
July 2018,
27
Ali Shafiei, Kamran Dehghani,
"Production of superhydrophilic glass and glaze
surfaces by pure water treatment", GLASS TECHNOLOGY-EUROPEAN JOURNAL OF GLASS SCIENCE AND TECHNOLOGY PART A,
Vol. 60,
Num. 3,
Page 65-72,
June 2018,
28
Seyed Hamzeh Seyed Ebrahimi, Kamran Dehghani, Jamshid Aghazadeh Mohandesi, Mohammad Bagher Ghasemian, Shahab Zangeneh,
"Investigation on microstructure and mechanical properties of Al/Al-Zn-Mg–Cu laminated composite fabricated by accumulative roll bonding (ARB) process", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 718,
Num. 0,
Page 311-320,
March 2018,
29
Ehsan Shafiei Liravinejad, Kamran Dehghani,
"Effects of thickness ratio and length of thickness transition zone on the tensile behavior of tailor rolled blanks", TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS,
Vol. 75,
Num. 2,
Page 30-35,
December 2017,
30
Maziar Jokari Sheshdeh, Farzad Mahboubi, Kamran Dehghani,
"Structure and tribological behavior of diamond-like carbon coatings
deposited on the martensitic stainless steel: The influence of gas composition
and temperature", DIAMOND AND RELATED MATERIALS,
Vol. 81,
Num. 1,
Page 77-88,
December 2017,
31
Ehsan Shafiei Liravinejad, Kamran Dehghani,
"Effects of thickness ratio on the total elongation of tailor rolled blanks", CANADIAN METALLURGICAL QUARTERLY,
Vol. 57,
Num. 0,
Page 1-8,
October 2017,
32
Seyed Siavash Firouzabadi, Malek Naderi, Kamran Dehghani, Farzad Mahboubi,
"Effect of nitrogen flow ratio on nano-mechanical properties of tantalum nitride thin film", JOURNAL OF ALLOYS AND COMPOUNDS,
Vol. 719,
Num. 0,
Page 63-70,
September 2017,
33
Hamid Alihosseini, Kamran Dehghani, Jamshid Kamali,
"Microstructure characterization, mechanical properties, compressibility and sintering behavior of Al-B4C nanocomposite powders", ADVANCED POWDER TECHNOLOGY,
Vol. 28,
Num. 9,
Page 2126-2134,
August 2017,
34
Ehsan Shafiei Liravinejad, Kamran Dehghani,
"Tensile behavior of tailor rolled blanks with longitudinal thickness
transition zone: Introducing a new tensile specimen", VACUUM,
Vol. 143,
Num. 0,
Page 71-86,
June 2017,
35
Hamid Alihosseini, Kamran Dehghani,
"Analysis of Particle Distribution in Milled Al-Based Composites Reinforced by B4C Nanoparticles", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 26,
Num. 4,
Page 1856-1864,
May 2017,
36
Ehsan Shafiei Liravinejad, Nooshin Goodarzi, Kamran Dehghani, A. Soltani Tehrani,
"A new constitutive equation to predict single peak flow stress curves at high temperatures: a comprehensive study on different steels", CANADIAN METALLURGICAL QUARTERLY,
Vol. 56,
Num. 1,
Page 104-112,
January 2017,
37
Mohsen Bodaghi, Kamran Dehghani,
"Friction stir welding of AA5052: the effects of SiC nano-particles addition", INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,
Vol. 88,
Num. 9,
Page 2651-2660,
January 2017,
38
Hamid Alihosseini, Kamran Dehghani, J Kamali,
"Manufacturing seamless square tubes of B4C-reinforced aluminum composites by extrusion", INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,
Vol. 0,
Num. 0,
Page 1-10,
October 2016,
39
Ehsan Shafiei Liravinejad, Kamran Dehghani,
"Prediction of Single-Peak Flow Stress Curves at High Temperatures Using a New Logarithmic-Power Function", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 25,
Num. 9,
Page 4024-4035,
July 2016,
40
Ali Chabok, Kamran Dehghani, A. Jazani,
"Comparing the Fatigue and Corrosion Behavior of Nanograin
and Coarse-Grain IF Steels", ACTA MATHEMATICA SINICA-ENGLISH SERIES,
Vol. 28,
Num. 3,
Page 295-301,
January 2016,
41
Seyed Siavash Firouzabadi, Kamran Dehghani, Malek Naderi, Farzad Mahboubi,
"Numerical investigation of sputtering power effect on nano-tribological properties of tantalum-nitride film using molecular dynamics simulation", APPLIED SURFACE SCIENCE,
Vol. 1,
Num. 367,
Page 197-204,
January 2016,
42
Mohammad Navazani, Kamran Dehghani,
"An analytical investigation on the effects of heat input on microstructures, phase transformations and mechanical properties of ultrafine grained Mg alloys fabricated by friction stir processing in different velocity ratios", Procedia Materials Science,
Vol. 11,
Num. 0,
Page 101-107,
November 2015,
43
Mohammad Navazani, Kamran Dehghani,
"Investigation of Microstructure and Hardness of Mg/TiC Surface Composite Fabricated by Friction Stir Processing (FSP", Procedia Materials Science,
Vol. 11,
Num. 0,
Page 509-514,
November 2015,
44
Seyedeh Fatemeh Tebyani, Kamran Dehghani,
"Effects of SiC nanopowders on the mechanical properties and microstructure of interstitial free steel joined via friction stir spot welding", MATERIALS & DESIGN,
Vol. 90,
Num. 0,
Page 660-668,
November 2015,
45
Hamid Alihosseini, M.Aslezaeem, Kamran Dehghani, Gh. Faraji,
"Producing High strength aluminum alloy by combination of equal channel angular pressing and bake hardening", MATERIALS LETTERS,
Vol. 140,
Num. 0,
Page 196-199,
November 2015,
46
Kamran Dehghani, Reza Ghorbani, A. R. Soltanipoor,
"Microstructural evolutions and mechanical properties of friction stir welding of 7075-O aluminium alloy", INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,
Vol. 77,
Num. 77,
Page 1671-1679,
November 2015,
47
Hamid Alihosseini, Kamran Dehghani, Ghader Faraji,
"Simulation of Fatigue Life Behavior of Circular Cross-Section Bar with Straight-Fronted Crack", Modeling and Numerical Simulation of Material Science,
Vol. 4,
Num. 3,
Page 128-135,
October 2015,
48
Mohammad Navazani, Kamran Dehghani,
"Fabrication of Mg-ZrO2surface layer composites by friction stir processing", JOURNAL OF MATERIALS PROCESSING TECHNOLOGY,
Vol. 229,
Num. 0,
Page 439-449,
September 2015,
49
Shahab Ranjbarbahadori, Kamran Dehghani, Seyed Ali Asghar Akbari Mousavi,
"Comparison of microstructure and mechanical properties of pure copper processed by twist extrusion and equal channel angular pressing", MATERIALS LETTERS,
Vol. 152,
Num. 0,
Page 48-52,
August 2015,
50
Shahab Ranjbarbahadori, Kamran Dehghani,
"Influence of intermediate annealing on the nanostructure and mechanical properties of pure copper processed by equal channel angular pressing and cold rolling", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 46,
Num. 7,
Page 2796-2802,
July 2015,
51
Morteza Ghafarpour, M. Kazemi, M. J. Mohammadi Sefat, A. Aziz, Kamran Dehghani,
"EVALUATION OF DISSIMILAR JOINTS PROPERTIES OF 5083-H12 AND 6061-T6 ALUMINUM ALLOYS PRODUCED BY TUNGSTEN INERT GAS AND FRICTION STIR WELDING", PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART L-JOURNAL OF MATERIALS-DESIGN AND APPLICATIONS,
Vol. 0,
Num. 0,
Page 1-13,
July 2015,
52
Tagh Ghorbanzadeh, A. Soltanipoor, Kamran Dehghani, Ali Chabok,
"Microstructural evolutions and mechanical properties of friction stir welded AA2024-3", PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART L-JOURNAL OF MATERIALS-DESIGN AND APPLICATIONS,
Vol. 230,
Num. 0,
Page 75-87,
July 2015,
53
Aliakbar Khamei, Kamran Dehghani, Reza Mahmudi,
"Modeling the Hot Ductility of AA6061 Aluminum Alloy After Severe Plastic Deformation", JOM,
Vol. 67,
Num. 5,
Page 966-972,
May 2015,
54
Seyed Hamzeh Seyed Ebrahimi, Jamshid Aghazadeh Mohandesi, Kamran Dehghani, M. Emamy, Sh. Zangeneh,
"The effect of Al-5Ti-1B on the microstructure, hardness and tensile properties of a new Zn rich aluminium alloy", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 636,
Num. 0,
Page 421-429,
April 2015,
55
Aliakbar Khamei, Kamran Dehghani,
"Effects of strain rate and temperature on hot tensile deformation of severe plastic deformed 6061 aluminum alloy", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 627,
Num. 1,
Page 1-9,
March 2015,
56
Aliakbar Khamei, Kamran Dehghani, Soroush Bakhshi, Kamran Kalaye,
"Hot and Cold Tensile Behavior of Al 6061 Produced By Equal Channel Angular Pressing and Subsequent Cold Rolling", Iranian journal of Materials Forming,
Vol. 2,
Num. 1,
Page 30-42,
March 2015,
57
M. Afrasiabi, Gh. Faraji, V. Tavakoli, M.M. Mashadi, Kamran Dehghani,
"The Effects of the Multi-pass Parallel Tubular Channel Angular Pressing on the Microstructure and
Mechanical Properties of the Cu–Zn Tubes", TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS,
Vol. 68,
Num. 5,
Page 873-878,
March 2015,
58
Seyedeh Fatemeh Tebyani, Kamran Dehghani,
"Friction stir spot welding of interstitial free steel with incorporating silicon carbide nanopowders", INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,
Vol. 79,
Num. 0,
Page 343-350,
February 2015,
59
Aliakbar Khamei, Kamran Dehghani,
"Hot Ductility of Severe Plastic Deformed AA6061 Aluminum Alloy", Acta Metallurgica Sinica-English Letters,
Vol. 28,
Num. 3,
Page 322-330,
January 2015,
60
Reza Nemati Chari, Kamran Dehghani, Abdolvahed Kami, Dorel Banabic,
"Application of response surface methodology for study of effective strain in equal channel angular pressing of AA6061 alloy", Romanian Journal of Technical Sciences-Applied Mechanics,
Vol. 59,
Num. 3,
Page 36-49,
December 2014,
61
Aboozar Aghaei, Kamran Dehghani,
"Characterizations of friction stir welding of
dissimilar Monel400 and stainless steel 316", INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,
Vol. 77,
Num. 0,
Page 573-579,
November 2014,
62
Arash Heydarian, Kamran Dehghani, Taymor Eslamkish,
"Optimizing powder distribution in production of surface nano-composite via friction stir processing", METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE,
Vol. 0,
Num. 0,
Page 1-6,
March 2014,
63
Mohsen Bahrami, Mohammad Kazem Besharati Givi, Kamran Dehghani, Nader Parvin,
"On the role of pin geometry in microstructure and mechanical properties of AA7075/SiC nano-composite fabricated by friction stir welding technique", MATERIALS & DESIGN,
Vol. 53,
Num. 0,
Page 519-527,
February 2014,
64
Mohsen Bahrami, Nader Helme, Kamran Dehghani, Mohammad Kazem Besharati Givi,
"Exploring the effects of SiC reinforcement incorporation on mechanical properties of friction stir welded 7075 aluminum alloy: Fatigue life, impact energy, tensile strength", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 595,
Num. 595,
Page 173-178,
November 2013,
65
Mohammad Javad Nayyeri, Kamran Dehghani,
"Microstructure Evolution in As-Cast and SIMA-Processed AE42 Magnesium Alloy", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 23,
Num. 9,
Page 3077-3084,
November 2013,
66
Kamran Dehghani, Maryamsadat Hosseini, Atiyeh Nekahi,
"Comparing the corrosion behavior of nanograined and coarse-grained interstitial free steels", INTERNATIONAL JOURNAL OF MATERIALS RESEARCH,
Vol. 104,
Num. 10,
Page 999-1006,
October 2013,
67
Shahab Ranjbarbahadori, Kamran Dehghani, Fatemeh Bakhshandeh,
"Microstructural homogenization of ECAPed copper through post-rolling", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 588,
Num. 588,
Page 260-264,
September 2013,
68
Shahab Ranjbarbahadori, Kamran Dehghani, Fatemeh Bakhshandeh,
"Microstructure, texture and mechanical properties of pure copper processed by ECAP and subsequent cold rolling", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 583,
Num. 583,
Page 36-42,
July 2013,
69
Mohsen Bahrami, Kamran Dehghani, Mohammad Kazem Besharati Givi,
"A novel approach to develop aluminum matrix nano-composite employing friction stir welding technique", MATERIALS & DESIGN,
Vol. 53,
Num. 53,
Page 217-225,
July 2013,
70
Amir Etaati, Kamran Dehghani,
"A study on hot deformation behavior of Ni-42.5Ti-7.5Cu alloy", MATERIALS CHEMISTRY AND PHYSICS,
Vol. 140,
Num. 1,
Page 208-215,
June 2013,
71
Amir Momeni, Kamran Dehghani, Gholam Reza Ebrahimi, Shahab Kazemi,
"Developing the Processing Maps Using the Hyperbolic Sine Constitutive Equation", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 44,
Num. 12,
Page 5567-5576,
June 2013,
72
Amir Momeni, Kamran Dehghani, M. C. Poletti,
"Law of mixture used to model the flow behavior of a duplex stainless steel at high temperatures", MATERIALS CHEMISTRY AND PHYSICS,
Vol. 139,
Num. 2,
Page 747-755,
May 2013,
73
Morteza Ghafarpour, Sina Kolahgar, Bijan Mollaei Dariani, Kamran Dehghani,
"Evaluation of Dissimilar Welds of 5083-H12 and 6061-T6 Produced by Friction Stir Welding", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 0,
Num. 0,
Page 0-0,
April 2013,
74
Amir Etaati, Kamran Dehghani, Gholamreza Ebrahimi, Hao Wang,
"Predicting the flow stress behavior of Ni-42.5Ti-3Cu during hot deformation using constitutive equations", METALS AND MATERIALS INTERNATIONAL,
Vol. 19,
Num. 1,
Page 5-9,
January 2013,
75
Mohammadhosein Musazadehmeybody, Kamran Dehghani,
"The effect of crystallographic orientation on sintering behavior of Ni nanoparticles: a molecular dynamic study", JOURNAL OF COMPUTATIONAL AND THEORETICAL NANOSCIENCE,
Vol. 10,
Num. 6,
Page 1-6,
January 2013,
76
Amir Momeni, Kamran Dehghani, Masoumeh Heydari, Mehdi Vaseghi,
"Modeling the flow curve of AISI 410 martensitic stainless steel", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 21,
Num. 11,
Page 2238-2243,
November 2012,
77
Ali Chabok, Kamran Dehghani,
"Effect of Processing Parameters on the Mechanical Properties of Interstitial Free Steel Subjected to Friction Stir Processing", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 22,
Num. 5,
Page 1324-1330,
November 2012,
78
Kamran Dehghani, Atiyeh Nekahi,
"Interactive effects of aging parameters of AA6056", METALS AND MATERIALS INTERNATIONAL,
Vol. 18,
Num. 5,
Page 757-767,
October 2012,
79
Movaffaq Kateb, Kamran Dehghani,
"Comparison of fracture behavior of sharp with blunt crack tip in nanocrystalline materials by molecular dynamics simulation", Journal of Modern Physics,
Vol. 5,
Num. 1,
Page 410-417,
May 2012,
80
Kamran Dehghani,
"Comparing the bake hardening of nano-grain AA6056 with its coarse-grain structure", International Journal of Modern Physics:Conference Series(IJMPCS),
Vol. 5,
Num. 1,
Page 335-341,
May 2012,
81
Hamid Alihosseini, Mohsen Asle Zaeem, Kamran Dehghani, Hossein Asghar Shivaee,
"Producing ultrafine-grained aluminum rods by cyclic forward-backward extrusion: Study the microstructures and mechanical properties", MATERIALS LETTERS,
Vol. 74,
Num. 1,
Page 147-150,
May 2012,
82
Hamid Alihosseini, Kamran Dehghani,
"Bake hardening of ultra-fine grained low carbon steel produced by constrained groove pressing", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 549,
Num. 1,
Page 157-162,
April 2012,
83
Mohammad Izadinia, Kamran Dehghani,
"Microstructural evolution and mechanical properties of nanostructured Cu-Al-Ni shape memory alloys", INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS,
Vol. 19,
Num. 4,
Page 333-338,
April 2012,
84
Hamid Alihosseini, Ghader Faraji, Ahmad Faez Dizaji, Kamran Dehghani,
"Characterization of ultra-fine grained aluminum produced by accumulative back extrusion (ABE)", MATERIALS CHARACTERIZATION,
Vol. 68,
Num. 1,
Page 14-21,
March 2012,
85
Amir Momeni, Kamran Dehghani, Xiang Xzung Zhang,
"Mechanical and microstructural analysis of 2205 duplex stainless steel under working condition", JOURNAL OF MATERIALS SCIENCE,
Vol. 47,
Num. 6,
Page 2966-2974,
March 2012,
86
Behzad Tolaminejad, Kamran Dehghani,
"Microstructural characterization and mechanical properties of nanostructured AA1070 aluminum after equal channel angular extrusion", MATERIALS & DESIGN,
Vol. 34,
Num. 1,
Page 285-292,
February 2012,
87
Amir Momeni, Kamran Dehghani,
"Microstructural Evolution and Flow Analysis during Hot Working of a Fe-Ni-Cr Superaustenitic Stainless Steel", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 42,
Num. 7,
Page 1925-1932,
December 2011,
88
Kamran Dehghani,
"Bake hardening of nanograin AA7075 aluminum alloy", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 530,
Num. 1,
Page 618-623,
December 2011,
89
Amir Etaati, Kamran Dehghani,
"Microstructural Evolution of NiTi47.7Cu6.3 Alloy during Hot Deformation", JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY,
Vol. 27,
Num. 10,
Page 951-960,
November 2011,
90
Mohammad Hossein Musazadeh, Kamran Dehghani,
"Molecular dynamic simulation of crack propagation in nanocrystalline Ni containing different shapes and types of second phases", COMPUTATIONAL MATERIALS SCIENCE,
Vol. 50,
Num. 11,
Page 3075-3079,
October 2011,
91
Hamid Alihosseini, Mohsen Asle Zaeem, Kamran Dehghani,
"A cyclic forward-backward extrusion process as a novel severe plastic deformation for production of ultrafine grains materials", MATERIALS LETTERS,
Vol. 68,
Num. 1,
Page 204-208,
October 2011,
92
Amir Momeni, Kamran Dehghani, Gholam Reza Ebrahimi,
"Modeling the initiation of dynamic recrystallization using a dynamic recovery model", JOURNAL OF ALLOYS AND COMPOUNDS,
Vol. 509,
Num. 39,
Page 9387-9393,
September 2011,
93
Hamid Alihossieni, Gholam Faraji, Kamran Dehghani,
"Producing Ultrafine Grain Al6061 Alloy by Accumulative Back Extrusion Process", JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,
Vol. 0,
Num. 0,
Page 0-0,
August 2011,
94
Amir Momeni, Kamran Dehghani,
"Microstructural Evolution and Flow Analysis during Hot Working of a Fe-Ni-Cr Superaustenitic Stainless Steel", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 42,
Num. 7,
Page 1925-1932,
July 2011,
95
Kamran Dehghani, Mehdi Mazinani,
"Forming Nanocrystalline Surface Layers in Copper Using Friction Stir Processing", MATERIALS AND MANUFACTURING PROCESSES,
Vol. 26,
Num. 7,
Page 922-925,
June 2011,
96
Kamran Dehghani, Ali Chabok,
"Dependence of Zener parameter on the nanograins formed during friction stir processing of interstitial free steels", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 528,
Num. 13,
Page 4325-4330,
May 2011,
97
Mahsa Mehranfar, Kamran Dehghani,
"Producing nanostructured super-austenitic steels by friction stir processing", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 528,
Num. 9,
Page 3404-3408,
April 2011,
98
Amir Momeni, Kamran Dehghani,
"Hot working behavior of 2205 austenite–ferrite duplex stainless steel characterized by constitutive equations and processing maps", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 528,
Num. 3,
Page 0-0,
January 2011,
99
Amir Momeni, Kamran Dehghani,
"Hot working behavior of 2205 austenite–ferrite duplex stainless steel characterized by constitutive equations and processing maps", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 528,
Num. 3,
Page 1448-1454,
January 2011,
100
Mohammad Izadinia, Kamran Dehghani,
"Structure and properties of nanostructured Cu-13.2Al-5.1Ni shape memory alloy produced by melt spinning", TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA,
Vol. 21,
Num. 9,
Page 2037-2043,
January 2011,
101
Amir Momeni, Kamran Dehghani,
"Microstructural Evolution and Flow Analysis during Hot Working of a Fe-Ni-Cr Superaustenitic Stainless Steel", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 0,
Num. 0,
Page 0-0,
December 2010,
102
Kamran Dehghani, Atiyeh Nekahi,
"Using Response Surface Methodology to Model the Age Hardening of AA6061", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 41,
Num. 12,
Page 0-0,
December 2010,
103
Ali Chabok, Kamran Dehghani,
"Formation of nanograin in IF steels by friction stir processing", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 528,
Num. 1,
Page 0-0,
November 2010,
104
Amir Momeni, Kamran Dehghani, Golam Reza Ebrahimi, Hamid Keshmiri,
"Modeling the Flow Curve Characteristics of 410 Martensitic Stainless Steel Under Hot Working Condition", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 41,
Num. 11,
Page 0-0,
November 2010,
105
Ali Shafiei, Parvin Abachi, Kamran Dehghani, Kazem Pourazarang,
"On the Formation of Intermetallics during the Furnace Brazing of Pure Titanium to 304 Stainless Steel Using Ag (30-50%)-Cu Filler Metals", MATERIALS AND MANUFACTURING PROCESSES,
Vol. 25,
Num. 11,
Page 1333-1340,
November 2010,
106
Amir Momeni, Kamran Dehghani,
"Prediction of Dynamic Recrystallization Kinetics and Grain Size for 410 Martensitic Stainless Steel during Hot Deformation", METALS AND MATERIALS INTERNATIONAL,
Vol. 16,
Num. 5,
Page 0-0,
October 2010,
107
Kamran Dehghani, Atiyeh Nekahi, Mohammadali Mohmmad Mirzaei,
"Using response surface methodology to optimize the strain aging response of AA5052", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 527,
Num. 27,
Page 0-0,
October 2010,
108
Aliakbar Khamei, Kamran Dehghani,
"Microstructural Evolution During the Hot Deformation of Ti-55Ni (at. pct) Intermetallic Alloy", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,
Vol. 41,
Num. 10,
Page 0-0,
October 2010,
109
Aliakbar Khamei, Kamran Dehghani,
"A study on the mechanical behavior and microstructural evolution of Ni60 wt%–Ti40 wt% (60Nitinol intermetallic compound during hot deformation", MATERIALS CHEMISTRY AND PHYSICS,
Vol. 123,
Num. 1,
Page 269-277,
September 2010,
110
Amir Momeni, Kamran Dehghani,
"Effect of hot working on secondary phase formation in 2205 duplex stainless steel", JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY,
Vol. 26,
Num. 9,
Page 0-0,
September 2010,
111
Atiyeh Nekahi, Kamran Dehghani,
"Modeling the thermomechanical effects on baking behavior of low carbon steels using response surface methodology", MATERIALS & DESIGN,
Vol. 31,
Num. 8,
Page 3845-3851,
September 2010,
112
Amir Momeni, Kamran Dehghani,
"Characterization of hot deformation behavior of 410 martensitic stainless steel using constitutive equations and processing maps", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,
Vol. 527,
Num. 21,
Page 0-0,
August 2010,
113
Kamran Dehghani, Mohammad Nasirizadeh, Saeed Bagherzadeh,
"Surface nanostructuring of interstitial free steel by wire brushing", PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART L-JOURNAL OF MATERIALS-DESIGN AND APPLICATIONS,
Vol. 224,
Num. 4,
Page 190-198,
June 2010,
114
Hassan Alihosseini, Kamran Dehghani,
"Modeling and Failure Analysis of a Broken Railway Axle: Effects of Surface Defects and Inclusions", Journal of Failure Analysis and Prevention,
Vol. 10,
Num. 3,
Page 233-239,
June 2010,
115
Kamran Dehghani, Atiyeh Nekahi,
"Artificial neural network to predict the effect of thermomechanical treatments on bake hardenability of low carbon steels", MATERIALS & DESIGN,
Vol. 31,
Num. 4,
Page 2224-2229,
April 2010,
116
Kamran Dehghani, Atiyeh Nekahi, Mohammadali Mohmmad Mirzaei,
"Optimizing the bake hardening behavior of Al7075 using response surface methodology", MATERIALS & DESIGN,
Vol. 31,
Num. 4,
Page 1768-1775,
April 2010,
117
Ali Akbar Khamei, Kamran Dehghani,
"Modeling the hot-deformation behavior of Ni60 wt%–Ti40 wt% intermetallic alloy", Journal of Alloys and Compounds,
Vol. 490,
Num. 490,
Page 0-0,
February 2010,
118
Kamran Dehghani, Ali Akbar Jafari,
"Finite element stress analysis of forging dies to improve their fatigue life", MATERIALS SCIENCE-POLAND,
Vol. 28,
Num. 1,
Page 139-152,
January 2010,
119
Hamidreza Farnoush, Amir Momeni, Kamran Dehghani, Jamshid Aghazadeh Mohandesi, Hamid Keshmiri,
"Hot deformation characteristics of 2205 duplex stainless steel based on the behavior of constituent phases", ,
Vol. ,
Num. 31,
Page 0-0,
January 2010,
120
Kamran Dehghani, [en-name N/A],
"Hot deformation behavior of 60Nitinol (Ni60 wt%–Ti40 wt%) alloy: Experimental and computational studies", ,
Vol. ,
Num. 527,
Page 0-0,
January 2010,
121
Hossein Abdollahi Ali Beik, Kamran Dehghani,
"Plotting the friction hills during the real industrial cold rolling of sheet", ,
Vol. 20,
Num. 71,
Page 81-88,
January 2010,
122
[en-name N/A], Kamran Dehghani,
"Modeling the microstructural evolution and effect of cooling rate on the nanograins formed during the friction stir processing of Al5083", ,
Vol. ,
Num. 527,
Page 0-0,
December 2009,
123
Hamid Keshmiri, Amir Momeni, Kamran Dehghani, Gholam Reza Heidri,
"effect of aging time and temperature on mechanical properties and microstructural Evolution of 2205 Ferritic -Austenitic Stainless Steel", ,
Vol. ,
Num. 5,
Page 0-0,
December 2009,
124
Maryam Salehi, Khorameh Farrokhzadeh, Kamran Dehghani, Amirhossein Kovkabi, Seyyed Hossein Yazdani Tabaie, Atieh Nekahi,
"Study of Vanadium and Niobium on the fatigue behaviour of Termite Weld", Journal of Welding Engineering,
Vol. 11,
Num. 34,
Page 26-30,
December 2009,
125
Hossein Abdollahi, Kamran Dehghani,
"Plotting the friction hills during the real industrial cold rolling of sheet", Amirkabir International Journal of Science & Technology,
Vol. 20,
Num. 70,
Page 0-0,
May 2009,
126
Kamran Dehghani, Hamid Naemi,
"Effect of Thermomechanical Proccessing on Forming Limit Diagrams Predicted by Neural Networks", ,
Vol. ,
Num. 23,
Page 0-0,
October 2008,
127
[en-name N/A], Kamran Dehghani,
"A New Model for Inverse Hall -Petch Relation of Nanocrystalline Materials", ,
Vol. ,
Num. 17,
Page 0-0,
October 2008,
128
Kamran Dehghani, Maryam Salehi, Mina Salehi, [en-name N/A],
"Comparing the melt-spun nanostructured aluminum 6061 foils with conventional direct chill ingot", ,
Vol. ,
Num. 489,
Page 0-0,
August 2008,
129
Maryam Salehi, Kamran Dehghani,
"Structure and properties of nanostructured aluminum A413.1 produced by melt spinning compared with ingot microstructure", ,
Vol. ,
Num. 457,
Page 0-0,
June 2008,
130
Kamran Dehghani, Amir Shafiei,
"Predicting the bake hardenability of steels using neural network modeling", MATERIALS LETTERS,
Vol. 62,
Num. 2,
Page 173-178,
January 2008,
131
Hossein Abdollahi, Kamran Dehghani,
"Irregularity in Friction Hills During the Cold Rolling of Materials", ,
Vol. ,
Num. 1,
Page 0-0,
January 2008,
132
Kamran Dehghani, [en-name N/A],
"Predicting The Bake Hardenability of Steels Using Neural Network Modeling", ,
Vol. ,
Num. 62,
Page 0-0,
January 2008,
133
Seede Morteza Mosavy Zadh Noghby, Kamran Dehghani, Majid Pouran-Vary,
"Failure Analysis of Automatic Coupler SA-3 in Railway Carriages", ,
Vol. ,
Num. 14,
Page 0-0,
July 2007,
134
Amir Momeni, Kamran Dehghani, M Torkan,
"bake hardening of a low carbon steel for automotive applications", ,
Vol. 0,
Num. 13,
Page 0-0,
January 2007,
135
Kamran Dehghani, Hossein Abdollahi, [en-name N/A],
"Analyzing The Cold Rolling of Aluminum Using a New Software (Matroll)", ,
Vol. ,
Num. 0,
Page 0-0,
September 2006,
136
Kamran Dehghani, J.J Jonas,
"Dynamic bake hardening of IF steels", ,
Vol. ,
Num. ,
Page 0-0,
May 2000,
137
Kamran Dehghani, J.J Jonas,
"Dynamic Bake Hardening of Interstitial -Free Steels", ,
Vol. ,
Num. 0,
Page 0-0,
May 2000,
138
Jamshid Aghazadeh Mohandesi, Kamran Dehghani,
"Effeect of coefficient of friction on shrinkage during aluminiunt sheet rolling", ,
Vol. 0,
Num. 0,
Page 0-0,
January 1994,